Fabtech 4" Basic System w/ Rear Performance Shocks 2019+ Chevy Silverado Trail Boss / GMC Sierra AT4 4WD

0 Review(s) Write a Review
Your Price: $1,659.58
Retail Price:$1,970.76
You Save:$311.18(16%)

Install Time: 5-6 Hours

Part Number: FAB-K1136
Availability: Special Order - On average, this product will take 26 business days for Mfr. to ship.

The Chevrolet Trail Boss and GMC AT4 both have a factory 2" lift compared to other GM 1500 trucks of the same year model. Fabtech’s suspension system for these two trucks provides a 4" lift height on top of the factory 2" lift for clearance of 35" tall tires. Once a Trail Boss or AT4 is lifted with a Fabtech 4" system, the truck will sit the same height as a 1500 with a 6" suspension and 35" tires.

Fabtech’s suspension design for the Trail Boss and AT4 provides excellent driveability both on and offroad. There is zero bump steer throughout the suspension cycle that helps reduce driver fatigue while improving the overall driveability of the vehicle.

The near-stock track width keeps the tires under the fenders for a clean appearance. Fabtech’s proprietary steering knuckle geometry provides an excellent lock to lock turning radius to maneuver in tight spots.

Heavy-duty 1/4" thick steel cross members feature OE style alignment cam pins that utilize the factory cams for easy adjustment. Triple front diff mounts reposition the differential for vibration-free operation at high speed.

The factory Trail Boss and AT4 Coilover shocks are retained and relocated from the bottom to allow for full steer while achieving 4" of lift. Rear lift is accomplished by removing the factory 2" block and replacing it with a 5" block and u-bolt system.

Fabtech has addressed all aspects of the Trail Boss suspension for proper wheel travel and lock to lock steering without over cycling. Comes with a free 5 year 60,000 mile Powertrain Warranty.

Features:

Crossmembers

1/4" thick steel lower control arm Crossmembers are arched for maximum ground clearance. The welded box design of these Crossmembers provides additional strength to the front suspension. Retains factory alignment cams for easy adjustment.

Steering Knuckles

Fabtech’s extended length ductile iron Steering Knuckles provide zero bump steer throughout the suspension travel. This provides an enhanced driver experience compared to stock. Near stock track, width keeps the tires under the fenders for a clean appearance.

Tie Rods

Oversized tie rods are provided to replace the stock units that are designed to handle oversized tires.

Coilover Spacers

The factory Coilovers are relocated with heavy-duty lower mounts to lift the vehicle while retaining the stock ride quality.

Skid Plate

A heavy-duty front differential Skid Plate is constructed of 1/4" thick steel to protect the diff from offroad obstacles.

Differential Mounts

Triple Differential Mounts properly reposition the front diff for the precise CV and driveshaft angle to reduce driveline vibration at high speed.

Sway Bar Mounts

1/4" thick steel drop brackets reposition the front sway bar for the increased ride height. This allows the sway bar link ends to fully cycle without binding throughout the extended travel range.

Rear Bump Stop Spacers

Billet spacers relocate the factory closed-cell bump stops to control the travel eliminating over cycling of the suspension.

Rear Lift Blocks

5" tall steel rear lift blocks replace the factory blocks for additional lift without changing the ride quality or load-carrying capacity.

Rear U-Bolts

American made U-Bolts designed to attach the entire rear differential to the vehicle. A critical part that demands the best quality for your vehicle.

Rear Performance Shocks

Extended length twin tube shocks provide a good highway ride with the ability to handle offroad use.

Tires & Wheels

  • Tire Size – 35/12.50R18 Wheel Size – 18×9 w/ 5" BS w/minor trimming
  • Tire Size – 295/70R18 Wheel Size – 18×9 w/ 5" BS w/minor trimming
  • Tire Size – 35/12.50R20 Wheel Size – 20×9 w/ 5" BS w/minor trimming
  • Tire Size – 295/65R20 Wheel Size – 20×9 w/ 5" BS w/minor trimming

Related Items

Fabtech 4
(0)
$1,728.28
Special Order - On average, this product will take 26 business days for Mfr. to ship.0
Fabtech 4
(0)
$3,158.95
Special Order - On average, this product will take 26 business days for Mfr. to ship.0
Fabtech 4
(0)
$3,499.38
Special Order - On average, this product will take 26 business days for Mfr. to ship.0

Accessories

Mickey Thompson Baja ATZ P3
(0)
$174.99
In Stock.106
Mickey Thompson Baja MTZ P3
(0)
$192.99
In Stock.47

Recently Viewed Items

0 Items
TOP